When materials have to move through a low shed entrance or between closely spaced stacks, machine size matters as much as lift capacity. The HIXEN HX2506 small telehandler is 2.02 m wide and 2.05 m high, with a short 4.00 m body measured to the fork carriage. It can unload palletized supplies in the yard, carry them to a covered storage area, and place them on a raised level. The telescopic boom offers a maximum lift height of 6 m and a maximum forward reach of 3.2 m. With four-wheel drive and a maximum lift capacity of 2,500 kg, the HX2506 suits farms, building supply yards, and smaller construction sites where access shapes how you handle materials.
Use the HX2506 fork load chart to check lifting capacity at your required height and forward reach. The chart applies to the machine on tires with forks and a levelling device at a 500 mm load center. Check both dimensions together to find the rated capacity for your planned lift.
The HX2506 is 2.02 m wide and 2.05 m high. The side view shows 4.00 m to the fork carriage and 5.22 m to the fork tips. Use these dimensions to check doorways, gates, and loading bays, allowing space for the fitted attachment and load when entering or turning inside.
| Parámetro | Especificación |
|---|---|
| Maximum lift capacity | 2,500 kg |
| Maximum lift height | 6.00 m |
| Maximum forward reach | 3.20 m |
| Overall length to fork carriage | 4.00 m |
| Overall length to fork tips | 5.22 m |
| Ancho total | 2.02 m |
| Altura total | 2.05 m |
| Distancia entre ejes | 2.80 m |
| Ancho de vía | 1.70 m |
| Distancia al suelo | 230 mm |
| External turning radius over tires | 4.50 m |
| Unladen weight with forks | 5,800 kg |
| Fork dimensions | 1,220 × 125 × 50 mm |
| Standard tires | 12-16.5 pneumatic |
| Standard engine | Yunnei YN27GBZ diesel |
| Standard transmission | Torque converter, 4 forward and 4 reverse gears |
| Drive | Four-wheel drive |
| Maximum travel speed | 35 km/h |
| Hydraulic flow and pressure | 85 L/min at 220 bar |
| Capacidad del tanque de combustible | 80 L |
Will the HX2506 fit through a 2.1 m doorway?
Measure the clear width and height separately. A 2.1 m high opening leaves just 50 mm above the nominal machine height, before accounting for thresholds, slopes, or equipment fitted to the machine. Share the opening dimensions and a photo of the approach so HIXEN can help check the proposed configuration.
Can the HX2506 lift 2,500 kg to 6 m?
The fork load chart places the 2,500 kg zone below the 6 m maximum lift height. For an elevated pick, check the allowable load at your actual placement height and forward reach using the chart for your fitted attachment and load center.
Is a small telehandler suitable for farm sheds and covered loading bays?
The HX2506 can move palletized feed, bagged supplies, and other materials between outdoor yards and covered work areas with suitable access. For enclosed spaces, check whether diesel equipment is permitted and whether the space has adequate ventilation. Also check floor capacity against the machine’s weight plus the load.
Can I use forks or a bucket I already own?
Send the attachment model, mounting dimensions, weight, and photos of the connection points. For powered attachments, include hydraulic flow and pressure requirements. HIXEN can review compatibility before you order.
How many HX2506 units fit in a shipping container?
The standard packing plan allows one HX2506 in a 20GP container or up to three in a 40HC container, with the pallet forks removed for transport. Share your destination port and any extra attachments so HIXEN can confirm the packing plan.
What should I send for a factory-direct quote?
Include your destination country or port, order quantity, and preferred options. If access or lift capacity is the deciding factor, send your narrowest opening, heaviest load, required lift height, and forward reach. HIXEN can quote the machine and help check both site fit and lifting requirements.
